Wnda3100v2 remote download wireless adapter drivers#

There are no drivers in the latest kernel that support this device. Also, on the side of the box it says this in

Wnda3100v2 remote download wireless adapter install#

> WNDA3100-100NAS (Windows install cd says WNDA3100v2, so I guess > My device: usb wifi: Netgear N600 Wireless Dual Band USB Adapter: Thanks for the stickies in the wireless section, those were helpful: If it does not in fact exist, should I use carl9170 or ndiswrapper? Or should I get a different device?

Wnda3100v2 remote download wireless adapter driver#

I’m guessing that the device driver exists since it’s given a UDI reference to freedesktop. v2 is not supported/ no native driver currently exists.

So I’ll worry about that later.ĭriver ‘usb_device_846_9011_0_if0’ not found at: Question: Is this even related to my usb wifi adapter? I’m guessing once I get the driver set up, I’ll see something about the firmware. Question: Where do I get this driver and where do I put it? I searched and couldn’t find usb_device_846_9011_0_if0.ġ6.701553] platform microcode: firmware: requesting intel-ucode/06-0f-06

Also, on the side of the box it says this in the ‘Package Contents’)īus 002 Device 003: ID 0846:9011 NetGear, Inc.Ģ.199745] usb 2-4: New USB device found, idVendor=0846, idProduct=9011Ģ.199749] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Ģ.199752] usb 2-4: Product: Remote Download Wireless AdapterĢ.199755] usb 2-4: Manufacturer: BroadcomĢ.199834] usb 2-4: configuration #1 chosen from 1 choice The only conclusion I can reach from that is that the bottleneck is at the USB drive, and specifically the way the router is handling wireless access to it (since speeds when my laptop is hardwired to the router are much better).My device: usb wifi: Netgear N600 Wireless Dual Band USB Adapter: WNDA3100-100NAS (Windows install cd says WNDA3100v2, so I guess these are the same thing. In other words, when my laptop is connected to the router wirelessly via the WNDA3100v2 11n USB dongle, upload/download speeds to/from the Backup NAS is around 100Mbps, but upload/download speeds to/from the attached USB drive average 40Mbps download and about 10Mbps slower on upload. HOWEVER, when my laptop is accessing the router wirelessly via the WNDA3100v2 11n USB dongle, it is able to read/write to/from the Backup NAS (which is not the USB drive, but rather a separate Buffalo Linkstation hardwired to the router via Cat6) at around 100Mbps. Haven't been able to improve this much at all no matter what I try. That's to/from my laptop and the USB drive attached to the router with my laptop hardwired to the router via Cat6 through my laptop's gigabit ethernet port.Īs indicated in the first post, with my laptop accessing the router wirelessly via the WNDA3100v2 11n USB dongle, I'm getting an average of about 40Mbps download from the USB drive (upload is a little slower). Wired Results (Cat6 Gigabit) to attached USB Drive: Wireless Results (5GHz Band Wireless N) to attached USB Drive: My Notebook (Wireless-N WNDA3100 USB Dongle Win7 Pro 64 bit)

Wnda3100v2 remote download wireless adapter for mac#

WNDR3700 Router (latest firmware, media server disabled, QoS on for MAC address of Vonage Device only)īroadcom NetXtreme 57xx Gigabit Controller If a setting is not referenced, that means it's at the factory default. My wired speeds are barely in that range.Īny suggestions on what I can do to improve my Wireless-N results? The following is my setup and the results I'm currently getting accessing the referenced attached USB drive. I must be doing something wrong because my wireless speeds are nowhere near that. I see some people in this thread have reported Wireless-N transfer speeds with this router of between 14MB/s to 18MB/s.